Magic Mesh Prep (Patent Pending)
 Product Fact
Sheet Tech Data Sheet MSDS
COMBINED LIQUID SCREEN DEGREASER, WETTING AGENT, AND ANTISTATIC
TREATMENT
 Magic
Mesh Prep is a ready-to-use liquid combining the properties of mesh degreaser,
wetting agent, and anti-static treatment. Magic Mesh Prep improves the flow
characteristics of liquids, facilitating more uniform coating of direct
emulsions and the easier transfer of ink during printing, thereby improving
printed image quality.
 The
improved wetting of mesh also promotes the adhesion of indirect and CDF®
Direct-Film (capillary system film), and improves the durability of all
stencil systems, for longer printing runs. The antistatic properties of
Magic Mesh Prep reduce the whiskering and feathering of ink when printing
under low humidity conditions.
INSTRUCTIONS
Step 1:
Apply Magic Mesh Prep uniformly with a brush on both sides of the mesh just
before stencil making.
Step 2: RINSE THE SCREEN THROUGHLY WITH WATER
Rinse the screen with tap water from both sides until any foam disappears
and the rinse water forms a uniform, sleek "film" of water on the mesh. Apply
indirect or capillary system films immediately after the rinse, while the
screen is still wet. The screen should be allowed to dry in a dust-free environment
before coating direct emulsions or applying direct/indirect system stencils.
CAUTION - Wear gloves, goggles, and a protective apron when using Magic Mesh
Prep.
PRODUCT DATA
Flash point: not applicable
TLV: not applicable
Color: orange
VOC: none
Density: 0.98 gm./cubic cm.
pH value: 4.7
Storage: 1 year in original container, at 68º F. (20º Celsius)
Disposal: Magic Mesh Prep can generally be emptied into drains, though it
is best to review MSDS with local authorities.
Microgrit
No. 2
An inert, abrasive powder that mechanically roughens or abrades nylon and
polyester.
Roughening increases the surface area of synthetic meshes for a better
mechanical bond with indirect films and direct emulsions; for better mesh
water retention for the adhering of CDF® direct-films; and for
extended stencil life with any stencil system. The particles in Microgrit
No. 2 are fine enough (18-20 microns) to pass through even the smallest
mesh openings. Do not use Microgrit No. 2 on natural silk mesh.
Instructions
- Dampen the screen with water.
- Sprinkle Microgrit No. 2 liberally on the printing side of the mesh.
- Rub the Microgrit No. 2 back and forth vigorously with a wet, stiff,
short-bristle nylon brush over the entire printing side. Or, rub a damp,
natural fiber rag back and forth across the printing side of the mesh
until the rag begins to fray.
- Thoroughly rinse the screen with water from both sides, including the
frame and frame corners.
- Degrease the screen with Screen Degreaser Liquid No. 3 before
attempting to make a stencil. For the convenience of roughening and degreasing
in a single step, and especially for larger screens, use Ulanogel 23.
Health & Safety Information
Microgrit No. 2 may be irritating if inhaled or if it comes into contact
with the skin or eyes.
First Aid: In case of contact with the eyes or skin, flush
immediately with water for 15 minutes and contact a physician.
No.
23 Ulanogel Roughening/Degreasing Gel
An abrasive degreaser gel that combines the actions of Microgrit No. 2
and Screen Degreaser Liquid No. 3.
The abrading action of Ulanogel 23 promotes better wetting of the mesh
and adhesion of the stencil, and thus, longer press life. Its degreasing
action removes dirt, dust, and oils from the mesh, reducing the risk of
stencil failure and pinholing.
Ulanogel 23 is ready-to-use and rinses off in hot or cold water. Its thixotropic
character permits easy and effective preparation of larger screens held
in a vertical position. Non-caustic - will not harm frames, mesh, or adhesives
on stretch and glue frames. Recommended for use with all stencil systems
on synthetic mesh only.
Instructions
- Dampen the screen mesh with water.
- Apply Ulanogel 23 to both sides of the screen and scrub vigorously with
a wet, stiff, short-bristle nylon brush on both sides of the mesh.
- Rinse the screen throroughly from both sides, including the inside edge
of the frame and the frame corners, with hot or cold water.
Health & Safety Information
Ulanogel 23 may be irritating if it comes into contact with the skin
or eyes.First Aid: In case of contact with the eyes or skin, flush
immediately with water for 15 minutes and contact a physician.
No.
25 All Mesh Prep
A ready-to-use liquid mordant that promotes mesh water retention and, thus,
the uniform adhesion of all Direct Films.
All Mesh Prep is especially helpful for use with thin CDF® Direct
Films applied to fine mesh, which inherently holds little water. All Mesh
Prep No. 25 rinses easily from the screen with hot or cold water. Non-caustic
- will not harm frames, mesh, or adhesives on stretch and glue frames. Recommended
for use with all CDF® Direct Films. Do not use on natural
silk.
Instructions
- Apply All Mesh Prep No. 25 only after the mesh has been thoroughly degreased
and immediately before adhering the Direct Film.
- Rinse both sides of the screen thoroughly with water.
- Apply All Mesh Prep No. 25 with a medium-stiff, long bristle nylon brush
to both sides of the screen.
- Let the screen stand for one or two minutes.
- Rinse the screen thoroughly from both sides with hot or cold water.
- All Mesh Prep No. 25 should be used no more than one hour before adhering
the film. If you do not proceed immediately to adhere the Direct Film,
re-wet the screen just before adhering the film.
Health & Safety Information
All Mesh Prep No. 25 contains a mild acid and may
be irritating over a prolonged period of time if it comes in contact with
the skin or eyes. First Aid: In case of contact with the eyes or
skin, flush immediately with water for 15 minutes and contact a physician.
No.
3 Mesh Degreaser Liquid
A degreaser solution that removes dirt, dust and oils from all meshs, new
and used.
Degreasing should be considered a first step in stencil-making, as it greatly
reduces the risk of stencil-making failure, extends on-press stencil longevity,
and alleviates pinholing. Screen Degreaser Liquid No. 3 is ready-to-use--no
mixing. Degreases effectively in hard water. Rinses clean with hot or cold
water. Non-caustic--will not harm frames, mesh, or adhesives on stretch
and glue frames. Reccomended for use with all Ulano stencil systems.
No.
33 Mesh Degreaser Concentrate 1:10
Instructions
- If using Screen Degreaser Concentrate No. 33, mix ten parts water to
one part Ulano No. 33.
- Apply to a wet screen from both sides with a wet, soft, long-bristle
nylon brush. Continue brushing until a light foam develops.
- Let the screen stand a few minutes until the foam subsides.
- Rinse the screen thoroughly from both sides. Including the inside edge
of the frame and the frame corners, with hot or cold water.
To Speed Stencil Removal
After ink removal, spray both sides of the screen with water and apply Screen
Degreaser Liquid No. 3 or Screen Degreaser Concentrate No. 33 as in degreasing
(above). Rinse with tap water. Degreasing helps remove oily ink residues,
washup solvents and makes the stencil more receptive to water-borne removal
chemicals. To Speed Stencil Removal
Health & Safety Information
Screen Degreaser Liquid No. 3 may be irritating upon prolonged contact
with the skin or eyes. First Aid: In case of contact with the eyes or skin,
flush immediately with water. If irritation develops, contact a physician.
Degreaser
Concentrate 1:20
Product Fact
Sheet Tech Data Sheet MSDS
Degreaser Concentrate 1:20 is a mesh degreaser liquid concentrate formulated
(after dilution) to remove dirt, dust, and oils from all screen mesh, new
or used. Degreasing should be considered a first step in stencil making, as
it greatly reduces the risk of stencil-making failure, extends on-press longevity,
and alleviates pinholing. Dilute Degreaser Concentrate 1:20 degreases effectively
in hard water and rinses clean with hot or cold water. It is non-caustic and
will not harm frames, mesh, or adhesives on stretch-and-glue frames.
INSTRUCTIONS
- Dilute Degreaser Concentrate 1:20 one part to twenty parts of water.
- Apply dilute Degreaser Concentrate 1:20 to a wet screen from both sides
with a wet, soft, long-bristle nylon brush. Continue brushing until a
light foam develops.
- Let the screen stand for a few minutes until the foam subsides.
- Rinse the screen thoroughly from both sides, including the inside edge
of the frame and the frame corners, with hot or cold water. AFTER PRINTING
After ink removal, spray both sides of the screen with water and apply
dilute Degreaser Concentrate 1:20 as in Step 2, above. Rinse with tap
water. Degreasing helps remove oily ink residues, washup solvents, and
speeds the action of stencil remover chemicals.
CAUTION
Degreaser Concentrate 1:20 may be irritating upon prolonged contact with
the skin or eyes. In case of contact with the eyes or skin, flush immediately
with water. If irritation develops, contact a physician.
PRODUCT DATA
Flash point: not applicable Color: red-orange Storage: 2 years (minimum)
at 68ºF (20ºC)
Disposal: Degreaser Concentrate 1:20 is biodegradable and can be flushed
down drains safely.
AVAILABILITY
- 1 quart (0.946 liters) 12 per case
- 1 gallon jug(3.785 liters) 4 per case
- 5 gallons (18.927 liters)
- 50 gallons (189.25 liters)
|
